start working on usb-usb converter port

2017-06-20 02:19:15 +02:00
parent 4757140107
commit d7d20e2511
16 changed files with 1481 additions and 0 deletions
@@ -0,0 +1,149 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET ?= usb_usb
+
+TMK_DIR ?= ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR ?= .
+
+# MCU name
+MCU ?= atmega32u4
+
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU ?= 8000000
+
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#MOUSEKEY_ENABLE ?= yes	# Mouse keys
+EXTRAKEY_ENABLE ?= yes	# Media control and System control
+CONSOLE_ENABLE ?= yes	# Console for debug
+#COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+#NKRO_ENABLE ?= yes	# USB Nkey Rollover
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+#LDFLAGS += -Wl,--relax
+
+#OPT_DEFS += -DNO_ACTION_TAPPING
+#OPT_DEFS += -DNO_ACTION_LAYER
+#OPT_DEFS += -DNO_ACTION_MACRO
+
+SRC = matrix.cpp
+
+#
+# Keymap file
+#
+# ifeq (yes,$(strip $(UNIMAP_ENABLE)))
+#     KEYMAP_FILE = unimap
+# else
+#     ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
+#         KEYMAP_FILE = actionmap
+#     else
+#         KEYMAP_FILE = keymap
+#     endif
+# endif
+# ifdef KEYMAP
+#     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+# else
+#     SRC := $(KEYMAP_FILE).c $(SRC)
+# endif
+
+# CONFIG_H ?= config.h
+
+
+
+# Search Path
+# VPATH += $(TARGET_DIR)
+# VPATH += $(TMK_DIR)
+
+
+
+# program Leonardo
+# PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV)
+
+
+
+include $(TMK_DIR)/protocol/usb_hid.mk
+include $(TMK_DIR)/protocol/lufa.mk
+# include $(TMK_DIR)/common.mk
+# include $(TMK_DIR)/rules.mk